Flare ICS to JB

Requirements:Win XP 32bit or Win 7 32bit(all tools set to Win Xp Sp3 Compatibility & Run as Admin)
Required Files:
RoadKill’s Disk Image
Link: DOWNLOAD
QualFast
Link: DOWNLOAD
EMMC Download
Link: DOWNLOAD
IMEI Writer Qualcomm Modem Tools
Link: DOWNLOAD
BP Firmware
Link: DOWNLOAD
AP Firmware
Link: DOWNLOAD
BuglessFlashable via Recovery Stock JB ROM
Link: DOWNLOAD
Drivers of Flare S100
Pcdrivers.zip
Chapter 1

1.1. Backup your ICS using Roadkill.
1.1.1.        Turn off your Flare, then press Volume down and power button at the same time. once you see the “ENTRY QPST DOWNLOAD”, open roadkill and click on Store Image Tab, select the disk with 3.61GB, click browse and select the location where you want your backup to be saved, and click start. Once finish proceed to next step.
roadkill
Chapter 2: WRITING

2.1. Write your IMEI1, IMEI2, Wi-Fi Mac, and Serial Number (S/N) in a piece of tissue paper.  XD

2.1.1. To do that, turn on your WiFi, and go to Settings > About Phone > Status. If some are missing just dial *#0000# in dial pad.

2.2. Extract all the filesyou downloaded. Make sure you remember the location of the file.



Chapter 3: JELLYBEAN INSTALLATION

3.1. Backup NVRam

3.1.1. Run EMMC_DownLoad_V1.2.3.exe ,(Check Download Boot Loader for 1st run)

3.1.2. Turn device ON (make sure USB Debugging is enable)

3.1.3. Connect phone thru micro USB cable (Note: Make sure there are no other USB Modem or phone connected to your computer except for Flare)

3.1.4. Click BackUp_NV.

3.1.5. Wait until back up is successful.

roadkill

3.2. Download BP Firmware (“ENTRY QPST DOWNLOAD” Mode)

3.2.1. Run EMMC_DownLoad_V1.2.3.exe. Click SELPATH select “BP Firmware” Folder.

3.2.2. Connect phone thru a microUSB cable. Check Device Manager for Com Port #.

3.2.3 Look for "Qualcomm HS-Usb Diagnostics 9006" type the Comport # in EMMC Download Box. Click Download.

3.2.4. Wait until download is successful (Usually it takes 6-12 sec). Remove battery. (Do not Close EMMC Download. then proceed to next Step )

roadkill





3.3. Download AP Firmware (Fastboot Mode) or (Green Screen Mode)

3.3.1. Run QUALFAST2.0.5.exe. Click SELPATH, select AP firmware (“Stock JB Rom” Folder),Check Format Card & Userdata

3.3.2. Press Power button and Volume Up simultaneously. (Fastboot Mode) "Green Screen"

3.3.3. Click OK to start download then connect phone thru a micro USB cable.

3.3.4. Wait until download is successful. Remove battery.





3.4. Restore NVRam Backup

3.4.1. Run EMMC_DownLoad_V1.2.3.exe.

3.4.2. Turn device ON. (make sure USB Debugging is enable)

3.4.3. Click Restore_NV. Browse and select bak.qcn file. Connect phone thru micro USB cable.

3.4.4. Wait until qcn restore is successful. (your IMEI 2 is Null & WiFi Mac Address is set to default. you need to write it again)



Chapter 4:IMEI 2 & Wi-Fi MAC Address Writing

4.1. IMEI 2 &Wifi Mac address Writing

4.1.1. Turn device ON (make sure USB Debugging is enable)

4.1.2. Locate your modem com port number (Go to Device Manager >Right-click “Tianyu HS-USB Android Modem 9025”> Properties > Advanced Tab > Advanced Port Settings > COM Port # (Ex. 10))

4.1.3. Open Qualcomm_Modem_Tools_V1.1.2.exe and type com port #

4.1.4. Write all your backup code, then click Write button. (In my case I have re-entered my IMEI1, IMEI2, S/N (Serial Number), Wi-Fi MAC)

Note: Every after successful entry of IMEI, the phone automatically restarts.



F. Restart Device. Wait until it boot perfectly

Chapter 5: Flash the BuglessFlashable via Recovery Stock JB ROM (already rooted)
                5.1. You know already how to do that.

					
Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s